How Do Hybrid Cars Save Gas

When it comes to hybrid cars versus gas cars and which one is better? The answer totally depends on your preferences and priorities. I’m sure that just like other people, you have had enough to pay and keep up with the high price of fuel. Perhaps, you are also concerned about the continuously worsening state of our environment and the fact that the fuel we use to power our vehicles isn’t a renewable resource and that once it’s gone, it’s gone. Whatever your priorities may be, hybrid cars are clearly a good choice. Besides being efficient when it comes to fuel consumption, it is also safe for the environment as it produces very little toxic emissions when compared to your usual gas powered vehicle. But the benefits don’t stop there. Shall we start with the basics?

Hybrid cars, as their name suggests, uses a hybrid of both gas powered engines and electric motors to power the vehicle and make it run. This means that it has two energy sources that work hand in hand in order to create enough power to get the car running without using too much fuel. In fact, you can choose to run your vehicle on electric power alone if the battery packs are fully charged. Only when the battery pack runs out of juice can you choose to use the gasoline motor. During traffic jams, this technology proves to be extremely beneficial as well. Can you imagine just how much fuel is burned during the long hours of bumper to bumper traffic? If you drive a hybrid, you need not worry about this because it actually turns of the gas engine automatically thus saving you from burning fuel unnecessarily. The bottom line? Compared to a gas powered vehicle, you will get more mileage out of your usual full tank if you drive a hybrid which would save you money because you need not fill your tank as much as you did before.

There is, however, one drawback to using hybrid cars. It is a bit more expensive than your usual car due to the technology that it uses. There are hybrid models that can be at least several thousand dollars more expensive than a gas powered car. But of course, with more people using hybrids and the increase in the number of companies that manufacture it, this price is expected to come down in the near future. For as along as the demand for this environmentally friendly car continues to exist and increase, the price reductions would subsequently follow. In a way, the car would paying for itself through all the savings that you make including those from the tax break that you will receive after you purchase a hybrid. So consider the benefits and weigh it against the price. I’m sure you’ll see just how worth it the vehicle truly is. Not only will you be able to cut your fuel consumption in half and save money because of it, you would also be doing the environment some good. What could be better than that? So do give the hybrid a try and see for yourself what a world of difference it makes.

4 Wheeler Cover

If you love to take your ATV on hunting, fishing or camping trips, it seems like the four-wheeler vehicle design was put together entirely with you in mind.  Before the age of the ATV, if you wanted to get really remote for a weekend in the wilderness, it meant taking your vehicle to the edges of where your car or truck could go and then hiking in.  This meant that there were vast areas of the wild that you could not explore much less hunt or fish in simply because you were limited by transportation.
An ATV solves that problem.  Equipped with a hearty four-wheeler, you can get deep in the woods or back to that remote lake or to a hunting area that was until now unattainable, set camp and enjoy a remote excursion that will surpass anything you have set out on before.  In that way, your four-wheeler literally becomes as much part of your hunting gear as your gun, ammunition and other necessities of spending several days roughing it in a remote area of the wilderness.
If have had any experience going on excursions like hunting, fishing or just camping, you know that the two critical components for success are experience and preparation.  Even though your four-wheeler might open up more room and horsepower to carry more gear to your campsite, the need to be prepared for every eventuality is just as important.  You would not even think about going into a camping situation without your tent.  Even if it is beautiful weather, you have to be prepared to use that shelter at night.  Similarly, if you have expensive equipment with you such as your gun or fishing gear, you bring bags or other protective covers to make sure that the elements will not ruin those important tools that you need for your outing.
The same is true of your ATV itself.  That is why an effective and hearty cover for four-wheeler is a must on a campout or hunting trip.  The elements are unpredictable as is the wilderness.  Even if you are not expecting rain or storms, the possibility of damage to your ATV while you are camped is sufficient to justify investing in a cover specifically designed for taking your ATV camping.
Along with the protective value, your ATV cover has over values to help you maintain a well run camp.  You can put other gear in the four-wheeler and cover it assuming those items will remain safe and dry.  Firewood, food items, maps or other paper products should be covered like this so even the morning dew cannot create problems.  Further, by look at this cover as a hunting aid, you can get an ATV bag that is camouflaged like your clothing and tent are to help you stay low key in the wild. 
The two important criteria of an ATV cover you will be using for many wilderness outings is durability and transportability.  That cover must compact down to a fairly small space so you can store it in a side pouch on your ATV in a way that does not take much space away from camping gear.  But most importantly, it has to be tough.  Camping excursions are roughing it experiences for man and gear.  So invest well in a quality four-wheeler cover for your hunting, fishing or camping outings and it will take good care of you for dozens of adventures in your future.

Things You Should Know Before Buying  4 Wheelers and Parts

Pontiac G5 Problems | Learn About Pontiac G5 Problems & Recalls

Pontiac G5 Problems | Learn About Pontiac G5 Problems & Recalls. If you are having problems with your Pontiac G5, you should read this article. The Pontiac G5 is an excellent vehicle, but it can have many problems that are expensive to repair. Don’t be forced to pay thousands of dollars to repair your Pontiac G5, consider getting an extended warranty for your Pontiac G5 now:

** Stop Worrying About Pontiac G5 Problems – Get A Free Pontiac G5 Extended Warranty Quote Today! **

The Pontiac G5 is a quality automobile, but like any vehicle on the road, it can experience serious problems with its engine, transmission, brakes or electrical system that can cost thousands of dollars to repair. The manufacturer’s warranty protects your Pontiac G5 from these problems for a little while, but once the warranty is over, you could be on the hook for a huge repair bill when your Pontiac G5 has a problem. You have nothing to lose and thousands of dollars to save by getting a free quote on an extended warranty quote for your Pontiac G5.

Click Here to Receive a FREE Quote on a Pontiac G5 Extended Warranty in 2 minutes – Save Hundreds of Dollars on an Extended Warranty for your Pontiac G5!

In this tough economy, you shouldn’t have to spend your hard earned money on car repairs. I hope that your Pontiac G5 never runs into any serious problems, but you should always be prepared just in case. The best way to protect yourself is by getting an extended warranty – click on the image below to get a free no obligation quote for a Pontiac G5 Extended Warranty in just two minutes:

H.i.d. Lights: Installation Guide

There really isn’t any doubt that H.I.D. lights are gaining a lot of appeal in the automotive industry. Ask most luxury car owners and it’s one of the things they have included in their “To Buy” list. In fact, these kits have slowly become a household name in the industry — thanks to the right combination of style and safety that it is becoming known for.
However, one question that most drivers ask is how easy HID lights can be installed. Actually, it’s as easy as changing the bulb of a semi-complex and sophisticated flashlight. What you need is a semblance of common sense, two working hands, an instruction guide that comes with the HID kit that you’ve purchased and a bit of trial and error from time to time.
Before you begin installing your HID lights, make sure that the crews are installed in their respective holes. This will prevent possible mishaps during the assembly process, since the screws might unpredictably go in at an angle, which consequently makes it much harder to turn and install the screws later on. Immediately installing them in their housing can prevent these problems from ruining your day.
Now that you have done the screws, the first step to installing your HID lights is to remove the battery’s negative cable. Remove the headlamp’s top cover, and manually position the door in the mid-position to remove it. Look for the manual override knob on the inside corner of each headlamp, and raise it to remove the bezels and top cover easily. Next, remove the headlamp assembly using a 10mm socket and ratchet, and once you’ve removed the assembly, use a sharp razor knife to score the aluminum headlight.  Once the headlight assembly is out of the way, slash the aluminum headlight bucket with a fine razor knife. The scored ribs must be removed to install the new HID headlight assembly.
Next, get your aluminum rib and break it off. After doing the first headlight bucket, tighten your vise grips when grabbing the aluminum to make sure that the edges are cleanly cut. Run the razor knife again if the aluminum does not break in your first try. After this, use a piece of two-sided tape to attach the ballast to the inner fender and strengthen the ballast by adding screws.  Don’t cover the serial number on the backside in case you need to replace your ballast. And also, make sure the headlamp assembly fits without frictions happening on any of the cut aluminum ribs.
After you’ve done this, put the screws by reaching around the sides of the headlamp bucket. Make sure to place some soft rags or blankets around the hood and fender to prevent falling pieces from rubbing and scratching the headlamp housing on the paint.
Now you can install the screws to firmly hold the ballast on the inner fender. Don’t exert too much force when putting the screws in place because the inner fender is light and prone to breakage. Once all the screws are placed, secure them carefully. Be extra careful in this process, too. The screws can cut into the plastic and break off the plastic mounting ears.
Now loosen the coolant reservoir and remove the battery protector to route the wiring under the battery tray. The battery protector pops out easily. Just press the plastic pushpin along the windshield edge to pull it out. Then, tie the cross wire harness in place by using tie-wraps. Make sure that you are careful around the hood hinges, as the wiring can be nipped if you leave it unlatched.
Once all the wires are in place, connect them to the ballast. However, make sure that you install the colored wires correctly — the battery and ground supply wires to the ballast should be installed with the red wire on the inside next to the inner fender and the black wire out.
Next, crimp the wire connectors together. Then, connect and tighten the battery wires to the stud on the fuse panel. Pay attention to the placement of the terminals so the plastic cover can be reinstalled.
After this, carefully connect the screws and tighten them afterwards. Once they are tightened, manually turn the headlights down into position to put it in its correct placement. One way to check if it is properly placed is through wiggles. The rule of thumb is that when it is wiggling, then you need to adjust it again.
Now, run the wiring under the reservoir by removing the coolant reservoir. It’s not necessary to remove the coolant hoses when the screws are already removed. As you can see, the negative battery cable is still separated, so do the final wiring connections at the frame ground stud. The black wires are joined here, and then the battery protector that you previously took out sits down on top of the stud.
By the way, when you are doing the wiring, refer back to the instructions provided by the company. You may find some headlamp wire connectors have missing wires. Don’t panic. This is quite normal in most products.  And also, you can prevent shorting by remembering to connect the single wires and thrusting the provided boot. Use a tie-wrap to grasp it out of the way of the headlamp during opening and closing.
There you have it. It doesn’t take a rocket science to install HID lights. Just follow these steps, and you’ll soon enjoy the benefits of having these lights installed in your vehicle.